Reasons Your fiat ducato remote key programming 500 Key Fob Won't Work

A fiat 500 spare key cut 500 key fob is a convenient way to open the doors and begin the car. There are a myriad of reasons the key fob might stop working. This could be due to a dead coin-battery, water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat punto key fob Replacement Flip Key Remote - an exact replica of the Ilco brand that must be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob not functioning. Modern key fobs have a very restricted operating range, and must be within just a few feet of the car to operate. If you're not close to your vehicle and you press the key fob button, the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this occurs, replace the coin-cell battery (Part Number CR2032) by a new one of a reputable brand like Panasonic Duracell or Energizer. They can be found in your local hardware store, or online.

After you've replaced the battery in the coin cell, you can test it by standing next to your fiat 500 keyfob 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switches.

If the key fob doesn't work after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module inside your car. Water damage can occur in a variety of ways, ranging from the slightest splash to submerging the fob in salt water at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to draw the moisture back out. If this does not work, you'll need to have the fob replaced by an auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob into the ocean or wash it in a machine. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually die. If you get the fob wet, it's not an ideal choice however, if you drop it into a cup of water or fail to take it out of your pocket before you run the washer Don't give up hope.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Then try the fob and see if it works. If the key isn't working it could need to be programmed again. This is usually done by a professional or dealer auto locksmith.

If the key is a newer model and hasn't been programmed to your vehicle, it will likely need to be replaced completely. A professional locksmith for cars will be able to complete this process. The locksmith will have to cut the key to match the ignition on your vehicle. They will also need to reprogram the fob to your car's system. This is a cheap and quick process that could be completed within the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob could stop working is that it's simply out of range. The remote's range is of 30 feet. Therefore, when you're too far from your vehicle it won't respond to your commands. You can solve this problem by moving the remote closer to your car until it responds.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board problem. In most cases, reprogramming the fob can resolve the issue. The instructions are available for most vehicles on YouTube or in the owner's guide.

It is possible to replace the metal clips that hold the coin battery in place. If they lose tension, it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob could be out of sync with your vehicle because of software or hardware problems. This could be a huge headache, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob for you. In some instances they might need to install the software again in your body control module, too.

Interference

In addition to a dead battery on a coin The key fob may not be receiving or transmitting an signal due to interference. This is possible when the key fob is close to an electronic radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons the key fob might not work could be due to a weak connection to the buttons and internal chip or water damage.

If the key fob failed to work one day in the middle of the night, or after trying every option at home to solve it e.g. battery replacement, reprogramming and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It converts the signals into electronic commands which are then read by the vehicle.

Fortunately, there's an easy way to reset all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers, which could help get your fiat scudo key replacement fob working again. If the issue persists, you should seek the advice of an expert technician. They will be able diagnose the exact cause of any problems.