Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are durable, long-lasting and easy to maintain. They do not get rotten or rusty like timber and aluminum.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will prevent unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause severe damage to your home and may even be fatal. It is essential to make sure that your windows are in good shape.

For single pane windows, it is relatively easy to replace them, and the new window will usually fit inside the frame that was previously installed easily. However when windows with double panes are secured by internal beading, it'll be more difficult to get rid of the panes that are in place and replace them with new ones. In this case you'll need to find some plastic spacers that aid the new pane in being able to fit perfectly into the frame of the window.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric and not onto the floor which could cause them to be trampled under.

It's a great idea to cover the gap with tape after the glass has been removed. This will stop drafts and water from entering your home until a professional arrives to fix the window. This also serves as an obstacle to stop intruders from making their way into your home. If the distance between the door and the window is substantial, you may prefer security screens that has an opening. This will provide the best of both.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash window. Over time, they can be affected by a variety of issues such as sliding. A sagging uPVC window can cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to shrink, it is important to act swiftly to stop the issue from getting worse.

Repositioning the hinges can aid in fixing a window which is sagging. You'll first need to open the windows to access the frame. After that, using the screwdriver, you'll be able to unscrew the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and verify the fitting. If you're satisfied with the fit of your window, tighten the screws to secure them in place.

If you are unable to move the hinges, you might have to replace the seal. As time passes, rubber seals lose their elasticity and dry out which causes them to lose tightness. It is important to replace your seal as quickly as you can to keep your upvc window repairs near me window waterproof and draughtproof.

uPVC handles can also become loose. This is usually due to screws that have become undone over time, but it could also be due to the mechanism of the handle wearing out. It's relatively simple to fix a loose uPVC hand. You'll first need to close the window and then perform an experiment fitting. The corners of the sash must align with the casing joint. If it doesn't then you can use the screwdriver to loosen up the handle. Then turn the mechanism into position.

3. Water Leaks

It is crucial to take action if wake up every morning to find a smoky wall and wet floors. Windows that leak water do can not only cause degradation of your home's structure but also hamper your efforts to control the temperature inside your home. The most frequent reason for leaks in upvc window repair near me windows is that the sealant surrounding the frame has been damaged or not present.

This is a relatively easy fix that can be completed by any DIY expert. Based on the severity of the issue the caulking that was used up might need to be removed before a fresh layer can be put on. It is essential to keep in mind that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk and then make the area harder to clean and could reduce the efficiency of your energy.

Check that any drainage holes have no debris in them, and also ensure that the sill pan has been properly angled to allow the water to drain from the window. In more severe cases, you may need to replace the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives in damp conditions and is able to quickly spread throughout the house.

It is also important to keep in mind that if the leak is coming from between the glass of your double glazed window repairs near me-glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sliding. This can be easily repaired by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open or it opens with a breeze. They can be replaced by any competent DIYer and can be completed in a matter of minutes.

Nearly every home in the UK will have either top hung or side hung uPVC windows that use hinges and, just like any mechanical component they will wear out over time. The process of replacing a hinge on a window is an easy procedure, but it is easier if you have someone to help you hold the frame in place.

It is also important to verify that the uPVC hinges are opened and closed in the correct direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The issue can be caused either by opening the window improperly or by a poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are happy to give assistance.

Regularly lubricating hinges is also essential. Applying an engineering lubricant that is light to the hinges is a good way to do this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also decreases the chance of windows sticking and prevent corrosion. This must be done at a minimum every year. WD40 and other solvent-based lubricants should not be used since they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by different causes. First, the hinges due to wear and tear could become misaligned. This can cause a gap to form where the sash joins the frame. This can be easily fixed by giving them a thorough clean, however if they are beyond repair it might be necessary to get them realigned or replaced. In addition, the interlock could also become unbalanced. This is located on the hinge's side, and may need to be cleaned. In certain instances it is possible to replace them.

The second most frequent reason for draughts are the window seals. They are prone to wear or damaged over time, and let air escape through the gaps. Replacement of these with high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help to regulate indoor temperatures and will lessen the risk of draughts.

The final method to cut down on the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler which can be hung over your window sill. These will keep your home warm by blocking cold air.

With a bit of regular maintenance and repair, your upvc windows will continue to provide a great level of insulation and security for your home. It is crucial to keep in mind that all windows eventually wear out and it is more cost-effective to replace them instead of fixing them. So, if you are experiencing issues with your Upvc windows, it's recommended to seek help from a professional as soon as possible.